Broadband Products AMC-6 Manual do Utilizador

Broadband Modem Installation Guide Release Versions AMC-6 72.0W Ku Band • StarConnect SAT VPN Software Version 2.02 • Broadband4PC Software

Figure 3-2 3. The software License Agreement will be displayed next as shown in Figure 3-3 below. Click Yes to continue with the software in

4. Windows XP will automatically select the Destination Folder. Click Next to continue (Figure 3-4). Figure 3-4 5. Windows XP will automatically

Figure 3-6 7. Windows XP will now begin the second phase of the software installation as shown in Figure 3-7. This may take several minutes dependi

9. The software License Agreement will be displayed next as shown in Figure 3-9 below. Click Yes to continue with the software installation. If you

Figure 3-11 12. Windows XP will now install the StarConnect Satellite VPN software into the appropriate locations on your computer (Figure 3-12

Figure 3-13 14. Once the StarConnect Satellite VPN software is installed, click Next to continue (Figure 3-14). Figure 3-14 15. Click Fini

Figure 3-15 16. After the software installation is completed, you must restart your computer for the software to take effect. Remove the CD fr

4 Entering Settings N Changing Transponder Frequencies Note: This section was included in the manual for future changes – Do NOT change current sett

Figure 4-3 3. This will now open your Transponder Management window as shown in Figure 4-4. Figure 4-4 4. Now highlight the transponder in

Figure 4-5 5. This will now show your Edit Transponder window. Please check to make sure that the Transponder is set to 11726, the Symbol Rate i

2 Contents Chapter 1: Getting Started - Installing Broadband Modem ...…...……….. 1-1 Package Contents 1-1 System Requirements 1-

Figure 4-7 Figure 4-8 7. Now go back to the Edit Transponder window and left click on OK as shown in Figure 4-9. Figure 4-9 20

8. You will now be on the Transponder Management window. Check to make sure that the Start Frequency and the End Frequency both have a value of

Figure 4-12 11. Now left click your mouse on the Status button as shown in Figure 4-13. Figure 4-13 11. The Transponder Status window will

Figure 4-14 12. Once you select manual Settings, change the Transponder to 11726, change the Symbol Rate to 8000, change the FEC to ¾ and the Pol

Figure 4-16 14. Once the Network box changes back to No Information (Figure 4-16) right click on the round signal (either red or green) in the Task

Figure 4-19 16. Now click Close on the Transponder Status window (Figure 4-20). Figure 4-20 17. Now left click on Close to close the Setup4PC win

Editing User Information 1. Right click on the double red computer screens in the Task Bar next to the clock (Figure 4-22). Figure 4-22 2. You w

4. Next, left click on File and then left click on Save. Once the file is saved, left click on File again and then left click on Exit (Figure 4-25).

6. Once your userinfo.txt file opens in Notepad, hold down the Delete key until both lines disappear. Then, you will need to change the first two

Figure 4-30 2. This will open your Setup4PC window as shown in Figure 4-31. Figure 4-31 3. Left click you mouse on the Data Services button as

3 1 Getting Started – Installing B2C2 Broadband Modem Package Contents Each package should contain the following items:  Either a TechniSat Inter

4. This will bring up the Data Services window as shown in Figure 4-33. First check to make sure that the MAC Source is set to User Defined IP. I

Figure 4-35 5 Dial-up Setup Windows XP 1. To create a dial-up connection in Windows XP, begin by left clicking on Start and then highlight t

Figure 5-2 2. Next, double left click on Internet Options (Figure 5-3). Figure 5-3 3. Once your Internet Options window is open, left cli

Figure 5-4 Figure 5-5 33 4. If you have any dial-up connection(s) currently set up in the Dial-up and Virtual Private Network Settings box, yo

Figure 5-6 5. Once they are all removed, click on the Add button to create a new dial-up for NRBB as shown in Figure 5-7. Figure 5-7 34 6. Th

Figure 5-8 7. Enter the phone number provided to you (local dial-up number) and then left click on Next as shown in Figure 5-9. Figure 5-9 8.

Figure 5-10 9. Now you will type your connection name in this box and then left click on Finish (Figure 5-11). Figure 5-11 10. Check to make

Figure 5-12 11. Next, select the radio button which states Never dial a connection as shown in Figure 5-13. Figure 5-13 37

12. Now click on LAN Settings as shown in Figure 5-14. Figure 5-14 13. Check to make sure that no boxes are checked in this window. If any boxes a

14. First left click on Apply to save the settings, then left lick OK to close the window (Figure 5-16). Figure 5-16 15. On your Control Panel d

Static Electricity Warning To prevent static damage to electronic components, observe the following precautions: Ì Touch an anti-static or groun

Figure 5-18 17. When Windows XP asks if you want to create the shortcut on your desktop, left click Yes as shown in Figure 5-19. Figure 5-19 Y

Figure 5-20 Figure 5-21 2. Next make sure that your boxes are checked as shown, then highlight Internet Protocol (TCP/IP) and left click on

Figure 5-22 3. Check to make sure that your settings match EXACTLY those shown in Figure 5-23. If they do not match, please change them according

4. Click OK on the Local Area Connection Properties window to close it (Figure 5-24). Figure 5-24 5. On the Network Connections window, look f

Figure 5-26 6. Next make sure that your boxes are checked as shown, then highlight Internet Protocol (TCP/IP) and left click on Properties as s

Figure 5-28 8. Click OK on the Local Area Connection Properties window to close it (Figure 5-29). Figure 5-29 9. On the Network Connections windo

Figure 5-30 Figure 5-31 10. Next, select Networking on the tabs across the top on the NRBB Properties window as shown in Figure 5-32.

Figure 5-32 11. Next make sure that your boxes are checked as shown, then highlight Internet Protocol (TCP/IP) and left click on Properties as shown

5-34 13. Click OK on the NRBB Properties window to close it (Figure 5-29). Figure 5-35 Close your Network Connections

Getting Online Double left click on your NRBB icon on your desktop. Type [email protected] under User name. Next, type yourpassword under Password

Installing External USB Satellite Modem To install the external USB satellite modem, do the following steps. There’s no need to turn off the co

50 Disconnecting from the Internet When you want to disconnect, just right click on your StarConnect SAT VPN icon (Fig 5-37) and select disconnec

2. The New Hardware Wizard window will appear (Figure 2-2). Click the bottom radio button to select “No, not this time” (If this window does not a

4. The computer will now search through the CD for the appropriate drivers (Figure 2-4). Figure 2-4 5. Select Continue Anyway when reported t

Figure 2-6 7. After Windows XP finds and installs the appropriate drivers, click Finish (Figure 2-7). Figure 2-7 8. Windows XP will then d

Figure 2-8 9. Remove the CD from the CD Rom drive and restart your computer. You have successfully installed the drivers and are ready to i